SATA Compliance Test Fixtures
!

TF-SATA-NE-ZP

1.5/3/6GB Test Fixture (Near end)
 

TF-SATA-NE-ZP facilitates near-end connection to the Serial ATA host or device under testTF-SATA-NE-ZP

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported, designed to meet or exceed SATA electrical specifications

Female SATA connector utilized, the same as is present at the end of an SATA cable

Test fixture plugs in to the host or device Serial ATA connector, in place of the Serial ATA cable

Differential 100 Ohm tight-tolerance controlled-impedance grounded coplanar waveguide (GCPW) PCB design

High-performance side-launch SMA connectors result in reduced torque from SMA cable connections,

and reduced stress on Serial ATA plugs and connectors

Complementary companion to TF-SATA-FE-ZP test fixture

Facilitates Serial ATA compliance testing when used with Tektronix® DPO/DSA70804 digital scilloscopes and P7380SMA and P7313SMA probes, or other manufacturers’ DSOs and probes

Facilitates Serial ATA compliance testing when used with Tektronix® Serial ATA Test Utility software

Note: Refer to document regarding a notice concerning possible HT/HR silkscreen mislabelling

TF-SATA-FE-ZP

1.5/3/6GB Test Fixture (Far end)

 

TF-SATA-FE-ZP TF-SATA-FE-ZP facilitates far-end connection to the Serial ATA host or device under test

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported, designed to meet or exceed SATA electrical specifications

Male SATA connector utilized, the same as is present in a SATA host or device

Test fixture connects to the far end of the host or device Serial ATA cable

Differential 100 Ohm tight-tolerance controlled-impedance grounded coplanar waveguide (GCPW) PCB design

High-performance side-launch SMA connectors result in reduced torque from SMA cable connections

Complementary companion to TF-SATA-NE-ZP test fixture

Facilitates Serial ATA compliance testing when used with Tektronix® DPO/DSA70804 digital

oscilloscopes and P7380SMA and P7313SMA probes, or other manufacturers’ DSOs and probes

Facilitates Serial ATA compliance testing when used with Tektronix® Serial ATA Test Utility software

 Note: Refer to document regarding a notice concerning possible HT/HR silkscreen mislabelling

TF-SATA-FEPD-ZP

1.5/3/6GB Test Fixture (Power-Data)

TF-SATA-FEPD-ZPTF-SATA-FEPD-ZP facilitates power-data connection to the Serial ATA laptop host under test

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported, designed to meet or exceed SATA electrical specifications

Utilizes a male SATA connector (as do the other "FE" test fixtures) which additionally supports power connections,

as is present in an SATA laptop drive

Test fixture connects to the Serial ATA laptop host

Differential 100 Ohm tight-tolerance controlled-impedance grounded coplanar waveguide (GCPW) PCB design

High-performance side-launch SMA connectors result in reduced torque from SMA cable connections

Provides power connection test points

Facilitates Serial ATA compliance testing when used with Tektronix® DPO/DSA70804 digital

oscilloscopes and P7380SMA and P7313SMA probes, or other manufacturers’ DSOs and probes

Facilitates Serial ATA compliance testing when used with Tektronix® Serial ATA Test Utility software

TF-SATA-IS-XP

1.5/3/6GB Test Fixture (In-system Monitoring)

 

TF-SATA-IS-XP facilitates in-system monitoring of Serial ATA data signals

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported

Male and female SATA connectors utilized

Test fixture plugs in to the host or device Serial ATA connector, and connects to the device or host

via a Serial ATA cable (not provided)

In-system access provided to all four Serial ATA differential signals

Accommodates differential probe connections through 0.15 inch-spaced (3,8 mm-spaced) PCB vias

Accommodates non-differential probe connections to ground through 0.15 inch-spaced (3,8 mm-spaced) PCB vias

Unique three-layer differential 100 Ohm controlled-impedance PCB design

Facilitates monitoring Serial ATA data signals in-system when used with appropriate high-performance digital

oscilloscopes and differential probes

Note: Refer to document regarding a notice concerning possible HT/HR silkscreen mislabelling.

TF-SATA-SET-III-ZP

Set comprising one each TF-SATA-FE-ZP, TF-SATA-IS-XP & TF-SATA-NE-ZP

TF-SATA-SET-IV-ZP

Set comprising one each TF-SATA-FE-ZP, TF-SATA-IS-XP & TF-SATA-NE-ZP + one additional TF-SATA-FE-ZP

TF-eSATA-NE-ZP

1.5/3/6GB Test Fixture (Near end)

 

TF-eSATA-NE-ZP facilitates near-end connection to the External Serial ATA host or device underTF-eSATA-NE-ZP test

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported, designed to meet or exceed SATA electrical specifications

Female External Serial ATA connector utilized, the same as is present at the end of an External Serial ATA cable

Test fixture plugs in to the host or device External Serial ATA connector, in place of the External Serial ATA cable

Mechanical reinforcement of the External Serial ATA connector for maximum durability

Differential 100 Ohm tight-tolerance controlled-impedance grounded coplanar waveguide (GCPW) PCB design

High-performance side-launch SMA connectors result in reduced torque from SMA cable connections,

and reduced stress on External Serial ATA plugs and connectors

Complementary companion to TF-eSATA-FE-ZP test fixture

Facilitates Serial ATA compliance testing when used with Tektronix® DPO/DSA70804 digital

oscilloscopes and P7380SMA and P7313SMA probes, or other manufacturers’ DSOs and probes

Facilitates Serial ATA compliance testing when used with Tektronix® Serial ATA Test Utility software

 Note: Refer to document regarding a notice concerning possible HT/HR silkscreen mislabelling

TF-eSATA-FE-ZP

1.5/3/6GB Test Fixture (Far end)

TF-eSATA-FE-ZP

 

TF-eSATA-FE-ZP facilitates far-end connection to the External Serial ATA host or device under test

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported, designed to meet or exceed SATA electrical specifications

Male External Serial ATA connector utilized, the same as is present in an External Serial host or device

Test fixture connects to the far end of the host or device External Serial ATA cable

Differential 100 Ohm tight-tolerance controlled-impedance grounded coplanar waveguide (GCPW) PCB design

High-performance side-launch SMA connectors result in reduced torque from SMA cable connections

Complementary companion to TF-eSATA-NE-ZP test fixture

Facilitates Serial ATA compliance testing when used with Tektronix® DPO/DSA70804 digital

oscilloscopes and P7380SMA and P7313SMA probes, or other manufacturers’ DSOs and probes

Facilitates Serial ATA compliance testing when used with Tektronix® Serial ATA Test Utility software

 Note: Refer to document regarding a notice concerning possible HT/HR silkscreen mislabelling

TF-eSATA-IS-ZP

1.5/3/6GB Test Fixture (In-system Monitoring)

 

TTF-eSATA-IS-ZPF-eSATA-IS-ZP facilitates in-system monitoring of External Serial ATA data signals

1.5 Gb/s, 3 Gb/s and 6 Gb/s bus signaling rates supported

Male and female External Serial ATA connectors utilized

Test fixture plugs in to the host or device External Serial ATA connector, and connects to the device or host

via an External Serial ATA cable (not provided)

Mechanical reinforcement of the female External Serial ATA connector for maximum durability

In-system access provided to all four Serial ATA differential signals

Accommodates differential probe connections through 0.15 inch-spaced (3,8 mm-spaced) PCB vias

Accommodates non-differential probe connections to ground through 0.15 inch-spaced (3,8 mm-spaced) PCB vias

Unique three-layer differential 100 Ohm tight-tolerance controlled-impedance PCB design

Facilitates monitoring External Serial ATA data signals in-system when used with appropriate high-performance

digital oscilloscopes and differential probes

Note: Refer to www.c-h-s.com/tf-sata.shtml regarding a notice concerning possible HT/HR signal pair swapping

and silkscreen mislabeling

TF-eSATA-SET-III-ZP

Set comprising one each TF-eSATA-FE-ZP, TF-eSATA-IS-XP & TF-eSATA-NE-ZP

TF-eSATA-SET-IV-ZP

Set comprising one each TF-eSATA-FE-ZP, TF-eSATA-IS-XP & TF-eSATA-NE-ZP + one additional TF-eSATA-FE-ZP